Color Analysis – CIE94 (ASTM E with ASTM D). Color Analysis – Hunter (ASTM E & ASTM D). Scope: Hunter Lab and XYZ are standard . This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee E12 on Color and. ASTM D Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates.
|Published (Last):||3 March 2018|
|PDF File Size:||13.10 Mb|
|ePub File Size:||20.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Both are appropriate for and widely used in industrial and commercial applications including, but not limited to, automobiles, coatings, cosmetics, inks, packaging, paints, plastics, printing, security, and textiles. wstm
Color Analysis – CIE94 (ASTM E1347 with ASTM D2244)
Send us a request Wilton UK: The are computed using the following ast, The three tolerance equations given here have been tested extensively against such data for textiles and plastics and have been shown to agree with the visual evaluations to within the experimental uncertainty of the visual judgments.
Use of a tolerance equation for other than daylight conditions will require visual con? A number in parentheses indicates the year of last reapproval.
Each subsequent color scale based on CIE values has 2 6. It is intended to be used as a single-number shade-passing equation.
The four more recently de? That implies that the equations themselves misclassify a color difference with a frequency no greater than that awtm the most experienced visual color matcher. Consequently, color differences are seldom if ever computed directly from differences in x, y, and Y. In the process, the researchers came to the conclusion that neither formula was truly optimum.
Lightness L99 5 Usually, the white object-color stimulus is given by the spectral radiant power of one of the CIE standard illuminants, for example, C, D65 e2244 another phase of daylight, re?
ASTM D – COLOR DETERMINATION
The equations derived and documented in standard DIN provides an axes rotation and the logarithmic expansion of the new axes to match that of the spacing of the CIE94 color tolerance formula without the need to make the specimen identi? Those conditions are given in Table 1.
The CIELAB metric, with its associated color-difference equation, has found wide acceptance in the coatings, plastics, textiles and related industries. Typically a 50 mm 2″ or mm 4″ disk Data: Formally confirming that your products and services meet all trusted external and internal standards. Nor is it possible or reasonable to plot groups of colors in terms of the modi?
ASTM D von Today, while instruments intended for use in color measurements share many common components, UV-VIS analytical spectrophotometers are designed to optimize their use in chemometric quantitative analysis, which requires very precise spectral position and very narrow bandpass and moderate baseline stability. Thus the equation is highly optimized for pairwise comparison of a product standard to a production test specimen but not for statistical process control.
In a typical recent survey Report No. An alternative method has been proposed 14 that corrects both problems: If you feel that your comments have not received a 2d244 hearing you should make your views known to the ASTM Committee on Standards, adtm the address shown below.
Additionally, the colorimetric spectrometer may also 2d244 able to report the underlying spectral data from which the colorimetric data were derived.
For specimens that are matte, randomly rough, or mildly textured, asm intermediate between 1: Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Where it is suspected that the specimens may be metameric, that is, possess different spectral curves though visually alike in color, Practice D should be used to verify d244 results.
There should not be a need to break the equation down into perceptual components—the CIELAB components of the model do that already. Current edition approved May 1, d224 The tristimulus values Xn, Yn, Zn de?
Link to Active This link will always route to the current Active version of satm standard. This is contrary to what is observed.
Specular component included for integrating-sphere measurements. Digital colorimetry allows atm tolerance atm the spectral scale and spectral bandwidth but demand much more stability in the radiometric scale.
Under these conditions, Xn, Yn, Zn are the tristimulus values of the standard illuminant with Yn equal to To avoid confusion, color differences among specimens or the associated tolerances should be compared only when they are obtained for the same color-scale system. The X-Rite i7 Colorimeter is highly automated.
Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. That implies that the equations themselves misclassify a color difference with a frequency no greater than that of the most experienced visual color matcher. Certification Formally confirming that your products and services meet all trusted external and internal standards.
However, for control of color in production, it may be necessary to know not only the magnitude of the departure from standard but also the direction of this departure. Need help or have a question?
Color Analysis – CIE94 (ASTM E with ASTM D)
It is possible to include information on the direction of a small color difference by listing the three instrumentally determined components of the color difference. Historical Version s – view previous versions of standard. Record the location where these measurements were made on the specimen.