The Microchip Technology Inc. 27C64 is a CMOS 64K bit (electrically) Programmable Read Only Memory. The device is organized as 8K words. 27C64 64k (8k X 8) CMOS EPROM FEATURES. High speed performance ns access time available CMOS Technology for low power consumption 20 mA. 27C64 EPROM Datasheet, 27C64 64K EPROM Datasheet, buy 27C
|Published (Last):||3 July 2009|
|PDF File Size:||13.82 Mb|
|ePub File Size:||19.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
If i wanted to select 01 on the Pushbutton switches how would that relate to the input states of the Eprom data lines? What is the function of TR1 in this circuit 3. Programming File for 27C64 Eprom I’m back again – sorry for the delay, I’ve suffered from a spine problem epro years, it causes unpredictable spasms that probably look quite comical to watch but having slipped and torn a muscle in my lower back the last thing I wanted was any sudden movements!
You have cleared up a lot of my confusion over this and have given me a Good place to start, time to do some serious study. I’m suspicious of the maximum voltage for logic 1 being 2.
Programming File for 27C64 Eprom Thanks Brian, Looks as though i might have to stick with the Eprom Idea for a bit longer, i have a few spare 27c64 available that i think are still good. This is exactly what is required, the Thumbwheel switches generate the line states from a Numerical setting 01,02,- 99, etc and the module displays these on the 7 seg Leds and switches the output lines to match, controlling the Radio Modules.
KRF4A 27c64 clone programming. If that isn’t physically epro, to do, with the power off, measure the resistance between the GND pin and nearby chassis to make sure they really are connected then use the chassis as the negative connection point.
Programming File for 27C64 Eprom It’s a static design, meaning there are no signal which change over 27c644 unless it’s because you change channel so yes you can use a DVM to check the logic levels. I have the Eproms for the TX and RX modules correctly burned with programming files provided by the equipment manufacturer Tait but i am lost as to how to create a BIN or Hex file from scratch to get the Channel Change Eprom to output the correct switching via its Data out lines.
27C64 – 27C64 64K EPROM Datasheet
Programming File for 27C64 Eprom Hello, Was wondering if someone that has had some experience in creating a BIN or HEX file suitable for a epgom Eprom could point me in the right direction re creating a file that would allow the above Eprom to control the output of its data lines D0 – D7 so that it eprok switch the lines either high or Low i.
Distorted Sine output rprom Transformer 8. Because of the strange way the EPROM address pins are connected, the input digits are reversed so if you want channel 10 you use address 01 instead. If this is true would i be able to measure with a Eprrom on DC volts the output state of the data lines out of the Channel Change eprom to confirm i have the correct lines either high or low to replicate the Dip switch settings on the Radio Eprom Board?
Choosing IC with EN signal 2. If I understand what you want, you have known input lines epfom and you want to convert them to different output line states by using the EPROM as a look-up table. Results 1 to 20 of 27d64 Heat sinks, Part 2: It would have to be replaced with an LCD but that introduces mechanical problems of fitting one in the same space. Each of the 4 bit patterns is translated to a single hexadecimal character like this: It’s fairly easy to do, first draw a table on graph paper or use a spreadsheet of the input states, these are the EPROM address lines.
When you have done it for all the input combinations you need, program the chip. I don’t mean to take up all of your time but i would be really interested in hearing more about the microprocessor option if you are able, there is plenty of space on the channel change module and might be easier to generate a small board that 27v64 plug in in place of the Eprom.
Part and Inventory Search. AF modulator in Transmitter what is the A?
Measure the voltages on all the Address lines and write down whether they are high or low as a binary number, for example: It’s better to share your questions and answers on Edaboard so we can all benefit from each others experiences.
Bin files i have erom before. Hierarchical block is unconnected 3.
Losses in inductor of a boost converter 9. Eprom image file for the prom in Power alarm system 0. You might be able to use binary but it’s horribly tedious. I assume the outputs from the EPROM are connected to the inputs of a PLL circuit so that different frequencies are selected for each combination of logic state. Bin Eprom file that we have been discussing?
For example, if you wanted EPROM channel 10 to produce an output of you would first reverse the channel digits and use address 01, then split the 8 bit output you want into two becomes then convert each to hexadecimal to find the number to store in the EPROM.
Last edited by tait ; 22nd April at It would be useful to note this because you may be able to use it to calculate new channel frequencies. Equating complex number interms of the other 6. The Channel Change module runs on 12V DC fed from the rack supply and if i can use this to power the Logic probe would this give me the ground signal for the probe to check the status of the lines?
The address lines are the inputs to the EPROM so they carry the number used to select the channel, you should see some of them change as you switch channels. It that is the case, and if the radio is working at the moment, I suggest you note the voltages on the EPROM outputs for each channel number you select. Not sure what you mean by “input states of the Eprom data lines”, the data lines are the outputs.
Programming File for 27C64 Eprom
Measuring air gap of a magnetic core for home-wound inductors and flyback transformer 7. Programming File for 27C64 Eprom.
The radio module Eprom is working correctly as i can manually select epro Channels via the 8 pin Dip switch and they follow the Dip Switch codes from the manual. ModelSim – How to force a struct type written in SystemVerilog? I am not fluent with Eprom programming and i have probably messed up the conversion from Binary to hex or placed it in the wrong location. I have a circuit Diagram of the unit and the input to the Eprom is already there with the BCD switching done by a pair of chips.
You will see distinctly different voltages on the pins and they will almost certainly be eprim close to 0V or 5V.