ASTM B specification refers to Alloy 20 Flanges intended for corrosive high temperature service. A sufficient discard shall be made from each ingot to secure . ASTM B Direct No.: + Fax No.: + Email: [email protected] Board No.: + Website: . Buy ASTM B Standard Specification for Forged or Rolled UNS N, UNS N, UNS N, UNS N, UNS N, UNS N, UNS.
|Country:||Antigua & Barbuda|
|Published (Last):||8 November 2006|
|PDF File Size:||8.69 Mb|
|ePub File Size:||11.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
A sufficient discard shall be made from each ingot to secure freedom from injurious piping and undue segregation. B — 04 Standard Speci?
ASTM B Nickel Alloy 20 Pipe Flange Supplier · ASTM B UNS N
The forgings shall conform to the specified sizes and shapes. In case of dissatisfaction with the results of the test, the producer or supplier may make claim for a rehearing. The product of UNS N shall be furnished in the annealed condition. However, the manufacturer of such forgings is responsible as required in accordance with Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Materials and Manufacture 5. When it is impractical to provide forgings for test purposes, test bars may be made from the billet or bar, provided they are given approximately the same reduction and heat treatment as the forgings.
ASTM B462 – Flange
Individual reprints single qstm multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Work Item s – proposed revisions of this standard. The material shall meet the requirements specified for the mechanical properties including tensile strength, n462 strength, and elongation.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
The material shall have a homogeneous structure as shown by the macroetch test in 7. Offer on Fasteners Sitemap. The test specimen, if cut from a?
Historical Version s – view previous versions of standard. Siddhagiri Metals and Tubes Rating: ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Rejection and Rehearing Link to Astn This link will always route to the current Active version of the standard.
The material shall conform to the chemical composition prescribed for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, copper, columbium, tantalum, nitrogen, iron, cobalt, tungsten, vanadium, titanium, zirconium, aluminum, yttrium, and cerium. This examination is a method to assure that no material grade mix-up has happened during manufacturing and marking of the product. The material shall conform to the chemical composition prescribed for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, copper, columbium, tantalum, nitrogen, iron, cobalt, tungsten, asstm, titanium, zirconium, aluminum, yttrium, and cerium.
ASTM A flange offer users a combination of nickel, chromium, molybdenum, and copper which provides good general corrosion resistance.
Forgings ordered under these speci? Requirements for forging done by hammering, pressing, rolling, extruding, or upsettinghot working, and heat treatment are detailed. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. This abstract is a brief summary of the referenced standard.
Alloy 20 flanges are best suited for mid-range corrosion use better than steel alloys. Examples of such requirements include, but are not limited to, the following: Mechanical Properties and Other Requirements 7. In such cases, the question of acceptable and unacceptable character of metal? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Number of Tests Requirements for forging done by hammering, pressing, rolling, extruding, or upsettinghot working, and heat treatment are detailed. Workmanship, Finish, and Appearance 9. Looking for some more information?
Flanges supplied by us are industry standard approved and certified.