BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.
|Published (Last):||6 July 2006|
|PDF File Size:||1.99 Mb|
|ePub File Size:||18.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
Before inserting a banana plug into the binding post be sure to mahual the post nut to avoid rattling and to provide full insertion of the banana plug. Bridged W 8 ohms Max. See diagram for details. This warranty gives you specific legal rights and you may also have other rights which may vary from province to province and country to country. Bryston will custom build cables for your application.
Tampering by persons other than factory authorized service personnel, or failure to fully comply with Bryston operating instructions, voids the warranty.
Wiring the SST amplifier also see rear panel description Speaker wires should be as short as practical. It’s a community-based project which helps b4 repair anything.
Push again and the amplifier will power-down. All SST amplifiers are convection cooled. The power up or turn-on of the 4B SST may be activated by remote control voltage. Never lift the safety ground to the amplifier nor remove the ground pin from the plug.
Bryston 4B SST C Manuals
When the power supplies have stabilized the channel will come out of mute and the LED will change to green normal operation. The balanced input requires a balanced pre-amp source. Spade lugs provide high contact area and secure fastening. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston. The 1v setting manuwl the most amplifier gain – 29 dB. Gold plated spade lugs are available from Bryston.
The speaker binding posts will accept wire up to 3 gage in size.
If both channel LED indicators are unlit the amplifier probably needs only to be powered on. The voltage is listed on the label found at the upper right of the rear panel. Bryston can provide an optional fan package if required. The 1v setting is used when the source is single-ended, or from a transformer coupled balanced source. Any SST channels thermally shutting down during operation indicates insufficient air flow, and a remedy must be found for cooling the amplifier.
The control current is determined by the source equipment. Then power the unit up normally.
Do not install directly above other heat generating equipment. The amplifier will now power-up only when the control voltage is present on. Clipping flashing red Clipping occurs when the channel output level no longer can follow the level increase at the input Overdriven input condition.
Bryston welcomes any suggestions you zst have, or comments regarding manuao operation of your amplifier.
Graph shows that distortion is essentially unaffected by load. The power up or turn-on of the 3B SST may be activated by remote control voltage.
Bryston 4B SST C Manuals
This is the home theatre setting for brystln operation Or use this setting with any systems where the volume control rotation is limited to the bottom half of the control or less. Master circuit – breaker. This includes parts, labour and return shipping to the first owner and all subsequent owners. Push firmly the center of the switch until the power-up sequence begins.
Cables should be kept as short as practical and should never be terminated with connectors that may become confused for AC power connectors. Input Manusl Gain Switch. Use quality wire, and if runs are more than 3 meters use at least 12 gage wire. Never operate the amplifier in a vertical position.
The optimum gain maual will depend upon the source pre-amp operating level, and or personal preference. Should the breaker trip, lower or remove the amplifier input signals.
The circuit feeding the 4B SST should be sufficient so as not to cause the circuit breaker to trip 15 amp min. This warranty is considered void if the defect, malfunction or failure of the product or any component part was caused by damage not resulting from a defect or malfunction or abuse while in the possession janual the customer. When the channel has cooled to a safe operating condition the channel will return to normal operation.
Different input configurations result in slightly different noise readings. Combinations may be used when bi-wiring. The above noise ratings represent minimum readings, actual readings may be better. On the rear panel is provided a high current plug for the power cord receptacle. Any amplifier that is constantly operated into clipping indicates a more powerful amplifier is needed for that application.
Bryston C Series 4B SST Dimensional Drawing
For this reason do not install anything directly above it. Note that copper wire is malleable and may require further tightening after the initial installation. In the unlikely event you have a problem and must return it for service you must use the proper packing material. Lugs should be gold plated. Banana plugs offer a quick disconnect option.
Also see installation section on ventilation.
Do not over tighten or the binding post may become damaged.