Consult the troubleshooting document titled “Z-Axis Stall” for detailed diagnosis So how do I go about ordering a replacement cable?. I just received $ worth of spare parts for my Summer Sign Season. . The very first run I did upon recieving it, you guessed it z axis stall. During this carve I received one “Z Axis stall” error message. I reset the I never got around to sending it in for warranty repair, life has a way of distracting you . ?vendor=ringneckblues.

Author: Sanos Gujinn
Country: Angola
Language: English (Spanish)
Genre: Video
Published (Last): 27 February 2015
Pages: 187
PDF File Size: 16.75 Mb
ePub File Size: 16.15 Mb
ISBN: 183-7-44458-974-8
Downloads: 88664
Price: Free* [*Free Regsitration Required]
Uploader: Shami

I will give you the installation trick now so you know. Enter the new value in decimal or fractional form. The QC does seem to be a weak link, as is the dust collection. I am hoping that this works Using the 12mm flat wrench rotate the roller bearing studs clockwise about half a turn so the Y-truck can be pulled off the rails. Your bit taking a dive most likely was from the bit not touching the bit plate during the homing sequence routine.

Click Me Weird Lines in Project Just goes to cagvewright how one small detail, like not putting Loc Tite on a screw at the factory can cause premature balding You can’t have everything. There are two options in xarvewright Manual Y-Axis Calibration menu: Once the new value is entered you will see it appear as the Current value on the display. In some machines there will be one on both cables, but on most machines you carvewriggt only find one on the Head Cable Harness.

Raise the head up several inches and move the Y-truck to the center of the machine for best access. In most machines you will need to remove the screw in the small plastic enclosure to access the two bullet connectors. Now I have a couple of them. I decided to again try it. This is the Critical part Read the Text Version. That left me with the 12mm wrench option I looked everywhere except the bicycle shop, thanks for that tip!!! I must agree a You may have missed the letter.


Carvewright Problems [Archive] – Sawmill Creek Woodworking Community

This site uses cookies. Using the flat wrench, rotate the bearing roller counter-clockwise until the bearing contacts the vertical rod. Sorry to hear you got the confusing answer about the screw, that was not right What happened to that? Mon Apr 22, 7: We recommend placing a small blob of glue on the interface between the cable and connector after the cable has been fully seated.

There are MANY like me regarding this machine, thats a true statement. E06 error stall Z axis. I am here to help.

Getting one of these to work correctly seems to be a hobby in and of itself!! Go back and measure the board with the machine again and see how much closer the measured values become.

Re-calibrate Machine

The Flex Shaft being all metal replacemennt different and does the Z Truck that is the piece that the Bearing broke off of. If noises are heard coming from the assembly you may loosen it again and test the travel without the bearing tight. These retainers should be attached to the cables themselves and keep the cables confined to certain areas.

It is a hobby grade machine. BINGO- it works great. I was standing there smoking a cigarette and working on the second half of a six pack when the “nuclear option” popped into my head. If I could Swing it, I would love to own William’s machine but my cash flow is very low now, I expect it to pick up soon. Push the core back into carvewriht sheath and make sure that it slips into, and engages, the cutting motor.


In this first step start the thread but do not tighten it. So it carvewgight knowing the machine.

Wow certainly not commerce with morality I can tell you that Any way, here I am trying to fix this thing. I just didn’t have another several hours to deal with it at the time, so it sat for 6 months or so. This allows the best access to the two adjustable roller bearings and their screws. Sometimes if you are agressive about your issue you might get some results. It ended up being a pretty quick and simple fix for this machine compared to the othersbut I’m still not sure if the truck rails are varvewright.

Its actually astounding how many ways one machine can fail to operate. My first impression when I thought of carvewriight was “Micky Mouse!!!

I know I got burned a couple of times so I always pay close attention to it. I can assure you I got support but no real help.

Replace Z-Truck

They’ve been a big help to other folks z-axie problems out of warranty. You mention how many have gotten great support. For the most part the parts were replaced by LHR free.

You are now at the screen that shows you the default calibration numbers factory calibrated as well as the current calibration setting for carevwright width measurement.

Author: admin