EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . Temperature controller. EKC MAKING MODERN LIVING POSSIBLE Sensors: Danfoss Pt, PTC or NTC • Calibration of sensors. RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D.
|Published (Last):||21 December 2013|
|PDF File Size:||13.55 Mb|
|ePub File Size:||16.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
It may however also be used as product sensor or condenser sensor.
Danfoss Temperature controller – EKC 102
Copying key not correctly mounted 5: None, defrost is based on time EKC A: A special moulding technique unites the hard front plastic, the softer buttons and the seal, so that they become an integral part of the front panel. There is no sensor -d-: Check delivery time and costs.
The possible functions are described in menu o All the mounted sensors must be of the same type. To avoid a too low setting of the setpoint, the min. When the controller demands refrigeration it will first cut in the compressor with the shortest 1022 time. High temperature alarm A2: It will cut out again when the temperature comes down to the set reference. The function is defined in o This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
The function delays the interval time d03 by the set number of minutes, but it only does it once, ekkc this at the very first defrost taking place when voltage is connected to the controller. All outputs are Off. The controller will then start a defrost cycle.
Digital input 2 of the controllers has a digital input which can be used for the following functions: All other outputs are Off.
Gives steps of 0. There will be re-start at 2 K below the setting. Sensor error on S5 E The actual defrost will be stopped based on time or temperature with a signal from a temperature sensor. Remove products Compare products.
HVAC Danfoss Electronic Temperature Controller type Danfoss EKC A B for Freezer
Refrigeration compressor or solenoid valve Defrost Alarm Refrigeration 2 compressor 2 Advantages: Manual control of outputs S Find the parameter code you want to change and push the middle buttons until value for the parameter is shown. Relay output 2 can be used for alarm function or for cutin and vanfoss of a refrigeration step 2. Set password Factory setting If you need to return to the factory-set values, it can be done in this way: The time delay is set in minutes. R22 Medium and high temperature scroll air-cooled condensing unit Box type air outlet from side scroll ZB series.
Controller for temperature control – EKC Manual |
Easy product returns Buy a product and check it in your own time, at home. All the mentioned methods can be used at random — if just one them is activated a defrost will be started. The value is the same as the one set for night setback, but will only be raised if danfpss value is positive.
The relay cuts in when lower temperatures are required. You can determine conditions of storing or access to cookie files damfoss your web browser.
Faults in the controller E The individual status codes have the following meanings: Fan Fan stopped at cut-out compressor Here you can select whether the fan is to be stopped when the compressor is cut out Delay of fan stop when compressor is cut out If you have chosen to stop the fan when the compressor is cut out, you can delay the fan stop when the compressor has stopped.
Order number or SW version do not match 9: The function is used as a simple defrost start, or it may be used as a safeguard if the normal signal fails to appear.
Enter your e-mail address, to which we will send a one-time notification when this product is available again. Interval between defrost starts The function is zeroset and will start the timer function at each defrost start.
Basic temperature control, precise control Up to 3 relay outputs: