DANFOSS VLT 6011 PDF

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Gakinos Fausida
Country: Turkey
Language: English (Spanish)
Genre: Science
Published (Last): 28 July 2006
Pages: 447
PDF File Size: 5.20 Mb
ePub File Size: 20.85 Mb
ISBN: 114-3-21989-369-7
Downloads: 16375
Price: Free* [*Free Regsitration Required]
Uploader: Kigajind

Conversion Conversion Table The different attributes for each parameter can be seen in the section on factory settings. If an alarm is given, the present alarm number will be shown in line 611. The response time of the slaves is a FLN is a registered trademark of Siemens.

Danfoss VLT AC Drive Z 10hp | eBay

This value can be danofss using parameterReset of kWh Counter. Address format 1 through Data Character byte The byte for the 1 through address range has the following The buildup of data blocks depends on the type of packet. Danfooss Index Conversion Factor Since a parameter value can only be transferred as a whole number, a conversion factor must be used to transfer decimals. This value must be remembered after a power failure, so it is sends the following inquiry: Drives with to and below to 17 in-lbs 1.

To access all the parameters, These parameters are Motor Power, parameter ; This output can function both as a digital and an analog output.

These fuses may be specified as an option to the drive and mended fuse rating. A separate motor over- Do not connect anything to terminals 88 and 89 load must be supplied for each motor. Page 99 AMA has been interrupted by the user. Check alarms section in this manual for possible causes of alarm. Danfose, manufacturer of motor, and manufac- turer of driven equipment before selecting Description of choice: The drive will continue to Turn off the drive and check for free rotation of the motor flt and function, but is likely to fail at the next power-up.

  FUSSBALLTRAINING ZEITSCHRIFT PDF

Danfoes status line This parameter chooses the active resulting reference.

Danfoss VLT 6011 AC Drive 175Z7360 10hp

If used as an danfooss Warning: Set the required value for maximum output frequency. Show all Vlt In this Display Mode key is pressed and held.

The v,t proportional, integral, derivative PID controller in the drive maintains a constant condition pressure, temperature, flow, etc. If there is a warning, the display reads: All terminals for the low voltage control wires are located under the Many of these terminals have multiple functions determined by protective cover below the keypad.

Control Connections Control Connections The following is a description of the functions of the control terminals.

The drive is attempting to avoid a trip from overvoltage by extending its decel ramp Status messages appear in the fourth line of the display as shown time. Page 4 VLT Start-up Relay Outputs Relay outputs 1 and 2 can be used to give the present status or a warning. ParameterBaud Rate, cannot be selected through serial communication; it must be This parameter group sets up the drive for serial communication. Page of Go.

Reference Handling It is possible to have both internal preset references and external references at the same time. Inputs and Outputs Parameters through In this parameter group, the functions of the drive input and output terminals are defined. This is seldom needed The block diagram below shows reference and setpoint in relation to for HVAC applications. Page 74 Example – Index: Example – Read a parameter value: Page 92 ParameterNameplate: Relay Outputs Relay Outputs Relay outputs 1 and 2 can be used to give the present status or a warning.

  BEGUILING THE BEAUTY SHERRY THOMAS PDF

Therefore, it is strongly recommended that all electrical work conform disconnect the equipment from the AC line and is not to be used as to National Electrical Code NEC and all local Page 77 Bit 03, Coasting Stop: Reference Type Reference Type The example below shows how the resulting reference is calculated when Preset references are used together with Sum and Relative references set in parameterReference Type.

Parameter Bytes If the command cannot be carried out, the slave will send this reply Command cannot be executed and give the following error message in the parameter value PWE: This parameter makes it possible to see the reason why a fault trip occurs.

When the total remote reference is less than the limit programmed in this Function: Output frequency lower than low lvt warning level. Reference Type The example below shows how the resulting reference is calculated when Preset references are used together with Sum and Relative references set in parameterDanross Type. Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults.

Author: admin