FAIRCHILD FMS7000 PDF

Fairchild/ON Semiconductor FMS is available at WIN SOURCE. Please review product page below for detailed information, including FMS price. 2B 1 ? Fairchild Semiconductor Corporation FMS Low Cost Five Channel 4th Order Standard De?nition. FMS part, FMS sell, FMS buy, FMS stock, FMS TSSOP New&Original pars, , Fairchild, +, New parts and Stock on hand.

Author: Galar Bagar
Country: Niger
Language: English (Spanish)
Genre: Travel
Published (Last): 9 January 2014
Pages: 234
PDF File Size: 5.96 Mb
ePub File Size: 18.31 Mb
ISBN: 911-5-93880-889-4
Downloads: 54544
Price: Free* [*Free Regsitration Required]
Uploader: Balkis

Following this layout con? Refer to the Layout Considerations section for more information. If the input signal does not go below ground, the input clamp will not operate.

Price 3 RON – 5 RON

F capacitor within 0. The worstcase sync tip compression due to the clamp will not exceed 7mV. DC-coupled inputs, AC-coupled outputs 0V – 1. Dimensions “D” does not include mold flash, protusions or gate burrs. Internal diode clamps and bias circuitry may be used if AC-coupled inputs are required see Applications section for details.

DC-coupled inputs and outputs 0. DC-coupling the fs7000 removes the need for output coupling capacitors. AC-Coupling Caps are Optional. A conceptual illustration of the input clamp circuit is shown below: Typical voltage levels are shown in the diagram below: For variation with an odd number of leads per side, the “center” lead must be coincident with the package centerline, Datum A. The input level set by the clamp combined with the internal DC offset will keep the output within its acceptable range.

  DORANTES ENDOCRINOLOGIA PDF

Frequency Response 10 5 0 -5 2 1 Figure 2. The value may need to be increased beyond ?

The FMS is speci? The video tilt or line time distortion will be dominated by the AC-coupling capacitor. Mold flash protusions or gate burrs shall not fairchold 0. Typical application diagram FMS Rev. Frequency 0. For multi-layer boards, use a large ground plane to help dissipate heat?

Allowable dambar protusion shall be 0. When the input fms0700 AC-coupled, the diode clamp will set the sync tip fms77000 lowest voltage just below ground.

The outputs can drive AC or DC-coupled single ? For optimum results, follow the steps below as a basis for high frequency layout: Datums — A — and — B — to be determined at datum plane — H —.

Dimensions “D” and “E1” to be determined at datum plane — H —. Dambar connot be located on the lower radius of the foot.

Circuite integrate

Terminal numbers are shown for reference only. F ceramic bypass capacitors? Dimension “b” does not include dambar protusion. Fzirchild internal pull-down resistance is k?

  KHO PING HOO PEDANG SINAR EMAS PDF

DAC outputs can also drive these same signals without the AC coupling capacitor. F, all outputs AC coupled with ? AC-coupled inputs and outputs External video source must 7. F in order to obtain satisfactory operation in some applications. For 2 layer boards, use a ground plane that extends beyond the device by at least 0. Care must be taken not to exceed the maximum die junction temperature. Interlead flash or protusion shall not exceed 0.

Dimension “E1” does not include interlead flash or protusion. In addition, the input will be slightly offset to optimize the output driver performance.

FMS – Fairchild Semiconductor – Hot Offers | Heisener Electronics

Minimum space between protusion and adjacent lead is 0. The offset is held to the minimum required value to decrease the standing DC current fms7000 the load. This dimensions applies only to variations with an even number of leads per side.

Author: admin