IEC 60332-3C PDF

Burning Behaviour of Bunched Cables. IEC The European Commission and The European Cable Industry (EUROPACABLE) are finalising. Definitions. IEC refers to various definitions, together with the following during the standard: .. F – B F. Category C, designation F – 3C F. IECC describes a method of type approval testing to define the ability of bunched cables to resist fire propagation. In this test, a cable specimen.

Author: Gardalrajas Zulujind
Country: Congo
Language: English (Spanish)
Genre: Art
Published (Last): 15 October 2011
Pages: 12
PDF File Size: 5.73 Mb
ePub File Size: 1.7 Mb
ISBN: 679-2-41783-667-4
Downloads: 15455
Price: Free* [*Free Regsitration Required]
Uploader: Tygoshakar

Reduced Fire Propagation in accordance with IEC |FAQ

The oxygen index of a material will drop when the temperature rises. Conversion of existing IEC apparatus to measure heat release is accomplished by fitting a small instrumented section of ducting into the exhaust system of the rig and using this with associated FTT gas analysis instrumentation and ief and a modified test protocol.

However, in European countries, halogen content, the corrosivity of the 603323-c, the smoke density and the toxicity of the gas are equally important factors affecting the safety and survival of human during a fire. The cable is deemed to pass the test if the flame spread will not extend to the upper portion and extinguish by itself. Test for vertical flame spread of vertically mounted bunched wires or cables. Resistance to fire alone — the cables is tested by gas burner flame isc passing idc current at its rate voltage.

This is a test defined by Naval Engineering Standard which is a directed at the analysis of a specified set of gaseous species which are commonly present in the combustion products of materials used in military application and which may cause lethality at the time of a fire.

  CANON D1120 MANUAL PDF

IEC TS | IEC Webstore

Compared with normal PVC cable, LSZH cable outperforms by its fire retardant properties, low corrosivity and low smoke emission properties, however, normal PVC cables has better mechanical and electrical properties.

The fire resistant cables exhibit same performance even under fire with water spray or mechanical shock situation.

Tests on electric and optical fiber cables under fire conditions – Part IEC and IEC are used to assess the flame propagation characteristics of a single wire. To determine if the cable is halogen free, IEC should be used.

Test for vertical flame spread of vertically-mounted bunched wires or cable – Category A -Installation In one layer front. This general purpose cables also meets UL The higher the toxicity index, the more toxic the cable material is.

Test for vertical flame spread of vertically-mounted bunched wires or cables – Category B -Installation In one layer front. Fire resistant cables are designed for maintaining circuit integrity during a fire. There are four primary fire testing standards as follows:. A fresh sample is mounted on a backing panel in a S bend and is exposed flames while the backing panel is stuck with a steel bar with same diameter as the cable under test every 30 seconds for 15 minutes.

The cable sample is deemed to pass this test if no fuse was ruptured nor any lamps extinguished during the 3 hour flame application and on re energizing the cable after 16 hours.

In general, the temperature index of fire retardant cable exceeds C. A Judges Scientific plc Company. Smoke Measurement Systems FTT can supply either laser or white light systems for smoke measurement in compliance with the standard.

This specifies a test for 60332-3 of smoke density. At room temperature, when the oxygen content 603332-3c the air exceeds the oxygen index, the material will burn by itself automatically.

  GREGORIO RICCI CURBASTRO PDF

System 6 UTP LSOH Cable (IEC 60332-3C) – International

No matter the cables are installed in single wire or in bundles, during a fire, the flame spread will be retarded and the fire will be confined to a small area, thus reducing the fire hazard due to fire propagation. Controls for the smoke measurement system if purchased. The specimen is deemed to have passed this test, of after burning has ceased, the charred or affected position does not reach within 50mm of the lower edge of the top clamp which is equivalent to mm above the point of flame application.

Riser cable is suitable for vertical shafts not defined as an environmental air plenum. Riser rated cables meets UL In this test, a 1 g cable specimen are completely burnt inside a sealed chambers of volume 0. The restricted cable meets ULLimited-use. The higher the oxygen index, the more retardant the cable is. The Classification utilises the results obtained from traditional IEC test equipment fitted with heat and smoke release measurement instrumentation. In general, the toxicity index of LSZH material is less than 5.

Fire resistant cables are designed to maintain circuit integrity of those vital emergency services during the fire.

The cables will be tested under the following temperatures: To qualify for a riser rating, the cables must have the flame spread of less than 12 feet beyond the ignition point.

Author: admin