First off, that’s not the industry standard. At least, not for any industry I’m familiar with. ARM-based MCUs like the Freescale Kinetis series or ST. M16C. From Wikipedia, the free encyclopedia. Redirect page. Jump to navigation Jump to search. Redirect to: Renesas Electronics#M16C microcontrollers. R5FMDFA#U0 from RENESAS >> Specification: Microcontroller, M16C Family M16C 60 Series Microcontrollers, 16bit, 25 MHz, KB, 31 KB.
|Published (Last):||24 January 2011|
|PDF File Size:||19.9 Mb|
|ePub File Size:||4.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
To read a string of bytes from a pre-determined memory address FFFC0 in this exampleuse code like this:.
Microcontrollers unique ID ?
There are many more MCU lines that are used quite a lot. Home Questions Tags Users Unanswered. Do I need a bootloader? Again from a availabiltity of tools, source codes and documentation point of view. Just a few things have to be taken care of, like connecting some pins of the MCU properly.
To read a string of bytes from a pre-determined memory address FFFC0 in this exampleuse code like this: I would prefer to save a ID in program memory.
For DIY projects, however, “industry standard” doesn’t matter. If your application provides a UART interface on UART1 of the device, and if the application has some jumper or so to set the device to flash programming you don’t need additional hardware for programming M Then ask specific questions here. Thank You both for these suggestions. There’s an industry standard microcontroller!!??
If you see a nice feature on the data sheet, then it’s worth it to consider Meaning, we can’t say what is better for you, that depends on your project. How can I achieve that? One option is to use a 1-wire “silicon serial number” chip DS The variable should be in a non volatile part of memory.
First off, that’s not the industry standard. Please read the help center to learn how to ask good questions. Start with something that you can understand using your existing level of knowledge and skill.
Schould I choose the generic boot device? However, the ATmega is only an 8bit MCU, and lacks the horsepower required for complicated projects.
Do I have to write a ID in memory first or does such a number already exist? Ok, now its clear. I know it’s the industry standard but what would it add to my simple project? Nothing is really superior in general, it’s more so what fits your project. At least, microconroller for any industry I’m familiar with. Are there any specifiers like: What are the advantages of working with the Renesas M16C microcontroller?
Each is guaranteed to have a unique bit serial number, and you only need to use up one pin of the MCU to interface with it. What matters is “community standard” i. You have given no explanation for what j16c need it for, so we can’t offer any rational, evidence-based analysis. So we can’t help you. There isn’t really such a thing as “the industry standard microcontroller” except possibly in some manufacturers’ marketing departments as something they like to tell themselves.
If you can’t understand it from the website and its datasheet, then it’s unlikely that you are going to be successful using it. The Renesas M16C is not an ‘industry standard’ for me. Usually, you go with a component that meets the need and nothing more. Many good questions generate some degree of opinion based on expert experience, but answers to this question will tend to be almost entirely based on opinions, rather than facts, references, or specific expertise.
If this question can be reworded to fit the rules in the help centerplease edit the question.
Indeed the availability of a good toolchain is the important thing and lots of support in online communities. I still have some questions: In any case I voted to close as too opinion based.
M16C – Wikipedia
Also downvoted due to very badly written. Another issue is that: This is provided as Visual Studio 6 source on the Renesas hompeage http: What if I use: Not to forget good readable datasheets. Anyway, if there is no such serial number how could I create one?
Who would’ve thought all that work I did on them 10 years ago would finally pay off So, to answer your question, I really can’t think of a reason why you should use a Renesas M16C.
I have to apologize because I have found the answer just a few posts below after posting this.